AS8 - КЛУБ ЛЮБИТЕЛЕЙ AUDI A8 и AUDI S8

First of all, sorry to write in English. I'm french. i don't speack russian.

Like many people here, i would like to "facelift" my Audi A8 2004 to Audi A8 2008 and i have a question about headlights.

My headlights now : 4E0 941 029 R and 4E0 941 029 R
My central electric now (calculator [9]) : 4E0 910 279 J
My headlight control now (calculator [55]) : 4E0 910 357

My question is : for facelift, i want to install the following headlights : 4E0 941 004 BE (10 pins) and 4E0 941 004 BE (10 pins). Is it possible by recoding or should i buy new headlight control [55] or/and new central electric [9] ?

Thanks a lot for your responses.

You need 4E0941003AE 4E0941004AE.
With these headlights you don't need to change control units, just change coding and add resistance in dimensions.

But if you want 4E0 941 004 BE, you need to change control units.

Akin писал(а):But if you want 4E0 941 004 BE, you need to change control units.

OK thank you very much. Do you know the part(s) number(s) that i must buy ?

Akin

я в этом деле

I will answer later. Now have't ETKA.

Your english is not too bad

Есть у нас ещё смайлы с английским? Хочется парню ответить Типа "спасибо, пожалуйста, с новым годом, пошёл на фиг"

akacio писал(а):

Akin писал(а):But if you want 4E0 941 004 BE, you need to change control units.

OK thank you very much. Do you know the part(s) number(s) that i must buy ?

Exactly to change the block 55 with the new number 4L0 907 357.
In block 09 try to drive a diode lamps encoding, if it does not, then change it as well. New number 4E0910279S.

Another is to consider that will have to pull new wiring. In the 14 pin chip consists of only 10.
It is much easier to put lights that I recommended in the first answer. Blocks intact. Pull the wiring is not needed.

Так вроде же запрещено на форуме не по-нашенскому

Ахренеть я где?!

OK but i already bought the headlights XX XXX XXX BE so i will change the 2 blocks.

When you talk about cables, do you talk about those : http://www.kufatec.de/shop/product_info ... A8-4E.html or there are more cables to change ?

This is not the correct cable.
I have not seen in the sale of the finished set of cables.
Need to make yourself.

Vladl писал(а):Так вроде же запрещено на форуме не по-нашенскому

Офигеть, я как-то забыл.
Прошу обойтись устным предупреждением.

интересно, а как это горячий французский парень вышел на наш форум?
а то может пора зарубежное представительство открывать?

Akin писал(а):Прошу обойтись устным предупреждением.

Jescha писал(а):Akin писал(а):
Прошу обойтись устным предупреждением.

First of all, thank you. I bought and installed the headlights (4E0941003AE & 4E0941004AE) and everything works fine... except one thing : I get an error on the dashboard when my right turn signal is activated. However, the bulb is good. Does anyone know why ?

Are the contacts the lamp seems good?

When you include reverse, lights whether the error?

What do you mean by "include reverse" ?

It means, does the fault come up when you set your gearbox in reverse?

Издержки автоматизированного перевода, в данном случае include - "включать", имеет значение "включать в себя", как часть чего-либо в общем. А "включать свет" уже будет switch on, turn on. Много значений короче...

No. No error when i set reverse light. Error only when i set turn right signal.

Then I think the problem is in coding unit.
What code is in the unit now?

[9] Central Electric (4E0 910 279 J) = 0133121
[55] Headlight Control (4E0 910 357) = 0000003